��HOW TO INTERFACE LED MATRIX WITH ARDUINO | ARDUINO TUTORIALS FOR BEGINN...

THE FOLLOWING VIDEO DEPICTS THE PROCEDURES REQUIRED TO INTERFACE THE LED MATRIX WITH ARDUINO MEGA.

THE COMPONENTS THAT YOU REQUIRE ARE:

1. ARDUINO MEGA.

2. SHIFT REGISTER.

3. BREADBOARD.

4. LED MATRIX MODULE.

TO START WITH THE INTERFACING PROCEDURE:

1. CONNECT THE CIRCUIT AS SHOWN IN THE SCHEMATIC GIVEN IN THE VIDEO.

2. WRITE THE CODE AS WRITTEN IN THE VIDEO. UPLOAD THE CODE AND YOUR LED MATRIX IS READY TO DISPLAY THE MESSAGE THAT YOU WANT TO DISPLAY.

# IMPORTANT:

DO THE CONNECTIONS CORRECTLY ELSE THE RESULT WON’T COME OUT ACCURATELY.

Comments

HOW TO MAKE A ROBOTIC BIRD | FLAPPING MECHANISM | GEARBOX DESIGN | ORNIT...

The following video aims at designing the flapping wing mechanism for a robotic bird (Ornithopter). The robotic bird can be controlled with a Remote Control. The design is made in solidworks software and the motion study of the mechanism is also done on the same software.

��HOW TO INTERFACE IR SENSOR WITH ARDUINO | VISITOR COUNTER | ARDUINO TUT...

(via https://www.youtube.com/watch?v=lkbPh8IV1t HELLO EVERYONE. TODAY WE WILL LEARN HOW TO INTERFACE IR SENSOR WITH ARDUINO AND HOW TO MAKE VISITOR COUNTER WITH IT. TO START WITH, AN IR SENSOR HAS 3 PINS, NAMELY FOR VCC, GND, AND DATA. THROUGH THE DATA PIN, WE TAKE IN THE INPUT AND DETECT WHETHER THESE IS SOME OBSTACLE IN FRONT OR NOT. IR SENSOR WORKS ON THE PRINCIPLE OF REFLECTION OF LIGHT WAVES. BY USING THE DIGITAL READ FUNCTION, WE CAN READ THE VALUE OF INPUT TO BE 1 OR 0, AND DO COMPUTATION ACCORDINGLY. TO MAKE THE PROJECT THE COMPONENTS REQUIRED ARE: 1. ARDUINO 2. LCD MODULE. 3. IR SENSOR MODULE. 4. BREAD BOARD. 5. POTENTIOMETER. 6. RESISTORS. 7. CONNECTING WIRES. CONNECTIONS: FOR LCD CONNECTION, YOU CAN VISIT MY PREVIOUS VIDEO AT: https://youtu.be/Li-ZkPfosvE NOW CONNECT THE DATA PIN OF THE IR SENSOR TO THE ANALOG PIN A0, OF THE ARDUINO. NOW YOU CAN PERFORM BOTH DIGITAL AND ANALOG READ FUNCTION ON THIS PIN, DEPENDING UPON YO...

��HOW TO MAKE DOOR LOCK SYSTEM USING ARDUINO | ARDUINO TUTORIALS | INTERF...

HELLO EVERYONE, TODAY WE WILL LEARN HOW TO MAKE A DOOR LOCK SYSTEM USING ARDUINO, KEYPAD, LCD, AND A SERVO MOTOR. TO BEGIN WITH, LET'S HAVE A LIST OF COMPONENTS THAT WE REQUIRE FOR THIS PROJECT: 1. ARDUINO MEGA. 2. LCD MODULE. 3. KEYPAD MODULE. 4. BUZZER. 5. RGB LED. 6. BREADBOARD. 7. CONNECTING WIRES. 8. RESISTORS. 9. POTENTIOMETER. ONCE, THE COMPONENTS ARE COLLECTED, WE NEED TO SETUP THE CIRCUIT, AS PER THE SCHEMATICS GIVEN IN THE VIDEO. ALSO YOU CAN SETUP INDIVIDUAL COMPONENTS LIKE 1. LCD: https://youtu.be/Li-ZkPfosvE 2. KEYPAD: https://youtu.be/nex5usOycSM 3. RGB LED: https://youtu.be/NLr56HLcWWk 4. SERVO MOTORS BY VISITING THE CORRESPONDING LINKS GIVEN ABOVE. AFTER THE CIRCUIT IS COMPLETE, YOU NEED TO UPLOAD THE CODE: #include<Keypad.h> // KEYPAD LIBRARY FOR KEYPAD INTERFACING #include<LiquidCrystal.h> // LIBRARY FOR LCD INTERFACING #include<Servo.h>// LIBRARY FOR SERVO MOTOR //#include<String.h> #define buzzer 10 // DEFININ...

Arduino Projects

Search This Blog